Ce site web utilise des cookies. Pour plus d'informations sur la façon dont nous utilisons les cookies, vous pouvez lire notre Notification sur la confidentialité et les cookies
3 articles seulement
Promotions
Livraison & Retours
Choisissez le lieu
Point relais
Livraison à domicile
Politique de retour
Retour gratuit dans les 7 jours suivant la date de livraison.Détails
Informations sur le vendeur
electronique morocco
86%Évaluation du vendeur
120 Abonnés
Performance vendeur
Taux d'expédition des commandes: Excellent
Score Qualité: Excellent
Avis des consommateurs: Moyen
Détails
Description
Arduino compatible shield that allows you to create a game console or robotic controller. It will mount on Uno or Mega 2560 style boards.
Power:
The shield has a voltage slide switch that allows you to select whether you are using it with a 5V board like an Arduino Uno or Mega 2560 or a 3.3V MCU like the Arduino Due. Be sure to set it to the correct voltage for the board you are using.
2-Axis Joystick:
The X-Axis potentiometer of the joystick is connected to A0. The Y-Axis potentiometer is connected to A1. The analog inputs on a microcontroller read values over a range of 0-1023 (for typical 10-bit ADC inputs). The X-Axis and Y-Axis controls should read around 512 (midpoint) when the control is at rest. As the joystick is moved, one or both of the controls will register higher or lower values depending on how the control is being moved. The joystick also has a button ‘K‘ which is activated by pressing the joystick down. This button is connected to D8.
Buttons:
There are a total of 6 buttons on the board (not including the one on the joystick) labeled A-F. The 4 large buttons are typically used for up/down/left/right or similar functions. The two smaller buttons are typically used for less commonly used functions such as ‘select’ or ‘start’ since they are less accessible / less likely to be pressed accidentally. All buttons have pull-up resistors and pull to ground when pressed.
- Button A – Connects to D2
- Button B – Connects to D3
- Button C – Connects to D4
- Button D – Connects to D5
- Button E – Connects to D6
- Button F – Connects to D7
Bluetooth Connector:
The RX/TX lines are brought out to a separate 4-pin female header along with 3.3V and Ground. This can be used for connecting a 4-pin 3.3V Bluetooth device or other TTL serial device.
I2C Connector:
The I2C SDA and SCL lines are brought out to a separate 4-pin male header along with 5V and Ground. This is in addition to the normal A4/A5 location of these lines. This allows for easy attachment of I2C devices.
nRF24L01 Connector:
This connector allows an nRF24L01 RF transceiver module to be plugged in.
2 x 4 Female Header
- GND – Ground.
- VCC – 3.3V
- CE – Connects to D9
- CSN – Connects to D10
- SCK – Connects to D13
- MOSI – Connects to D11
- MISO – Connects to D12
- IRQ – No Connection
Nokia 5110 LCD Connector:
This female header connector is designed to mount the Nokia 5110 LCD that was originally designed for Nokia phones and provides a 48×84 pixel matrix.
This interface occupies the same D9-D13 pins as the nRF24L01, so you can’t use both at the same time. If not using either of these devices, these pins are available for general purpose use.
Interface Header:
This dual row yellow male header provides another point of access to all the buttons, joystick pots, 3.3V, 5V and Ground. The pin-out of this connector is labeled on the board to the left of the connector.
Fiche technique
Principales caractéristiques
- 2-Axis joystick
- 4 large buttons
- 2 small buttons
- Bluetooth / Serial interface
- I2C interface
- nRF24L01 interface
- Nokia 5110 LCD interface
- Interface connector
- Power switch to switch between 3.3 and 5V
Vendu avec le produit
Descriptif technique
- SKU: GE232TG17RCAXNAFAMZ
- Modèle: arduino funduino Joystick Shield
- Pays de production: China
- Couleur: Multi-color
- Matière principale: 1
Commentaires des clients
Les clients ayant acheté ce produit n'ont pas encore émis d'avis.