الصفحة الرئيسية المنزل والمطبخ أدوات تجهيز المنزل أدوات كهربائية أدوات ومعداتGénérateur haute tension Module DC 3V-6V Bis 1000kV Boost Step Up .1PCS

Générateur haute tension Module DC 3V-6V Bis 1000kV Boost Step Up .1PCS

125.00 Dhs

148.00 Dhs16%

6 units left

التوصيل من 7.00 Dhsالي الدار البيضاء- انفا

5 out of 5

(‎2‎ تقييمات موثقه)

اختار خيارات أخري

عروض

طلبات جوميا إكسبريس مؤهلة للشحن المجاني. العرض خاضع للشروط لأي استفسار أو مساعدة في تقديم الطلب، اتصلوا بنا على : 18 18 04 22 05

إبلاغ عن بيانات غير صحيحة في المنتج

التوصيل والارجاع

اختار العنوان

محطة الاستلام

مصاريف الشحن 7.00 Dhs

جاهز للإستلام من ‎11 دجنبر‎ إلى ‎12 دجنبر‎ إذا أكملت طلبك خلال ‎15hrs 56mins‎

توصيل للمنزل

مصاريف الشحن 18.00 Dhs

جاهز للتوصيل من ‎11 دجنبر‎ إلى ‎12 دجنبر‎ إذا أكملت طلبك خلال ‎15hrs 56mins‎

سياسة الارجاع

إرجاع المنتج مجانًا خلال 7 أيام بشروطتفاصيل

بيانات البائع

GREEN YEAR

70%تقييم البائع

61 المتابعين

تابع

أداء البائع

معدل سرعه توصيل الطلب: جيد

تقييم الجودة: ضعيف

تقييم العملاء: جيد

مواصفات المنتج

This high-voltage module is made by using the principle of Tesla coil, and outputs high-voltage pulse high-voltage current. It is small in size, high in efficiency, and simple in peripheral circuits (just connect the switch and the battery can be used). The discharge intensity is violent.

Input voltage: DC 3V-6V
Input current: 2A-5A
High voltage type: pulse current type
Output voltage: about 200,000 volts (please pay attention to safety when using)
High voltage two-pole discharge distance: 10mm-20mm
Output high voltage line length: about 100mm
Input power cable length: about 100mm (red wire is positive)
Dimensions: Φ24*64mm
About the power supply: you can use a single 3.7V lithium battery or two in series, such as 18650 battery, an idle mobile phone battery (to remove the protection board, the recommended capacity is above 2000mAh) or NiCd/NiMH battery pack, 4V or 6V lead-acid battery etc.

This module is a finished module of a high-voltage inverter transformer/booster for scientific production. After inputting DC3V-7.2V voltage at the input end, a DC high voltage of about 200,000 volts (about 1-2 cm arc) can be obtained at the output end. , note that there is no ignition function

Wiring: The red wire is the positive pole of the power supply. The output is 2 high temperature and high pressure resistant silicone wires

المواصفات

المواصفات الرئيسية

Product usage: The module is divided into the input end and the output end, the red green (white) line is the input end, the red positive green (white) negative, two thick color of the same high voltage wire is the input end, fixed the output end of the appropriate arc distance, the input end of the battery can produce high voltage or high temperature arc.
Notes on module use:
1. the high voltage module should avoid the use of high voltage no-load power, before power must adjust the high voltage line end of the appropriate distance, the high voltage line arc distance is proportional to the use of battery voltage and capacity.
2.The arc distance should be tested from short to long, and it is strictly prohibited to exceed the longest arc distance when energized, because the high voltage energy can not be released, it is easy to damage the module.
3, the power of the module is large, the internal heat dissipation is not suitable, so it can not work for a long time.
4. The way to determine whether the battery capacity can drive the maximum power output is to measure the battery voltage when the arc is pulled. If it is around 6V, it can output the maximum power.
5. the small-capacity lithium battery two sections in series is 7.2V (series is not recommended), in the arc state measurement voltage has fallen to about 4V, the smaller the capacity of the voltage pull lower. Therefore, it is recommended to use more than 2000MA lithium battery, and it is best to match 4000MA battery.